Japanese Industrial Standards Data – Aluminum alloy die casting
A chart listing aluminum alloys for die-casting standardized by the Japanese Industrial Standards.
Japanese Industrial Standards
JIS H 5302 : 2006
Aluminum alloy die casting
Preface
The chart below is from the Japanese Industrial Standards and is based on the information contained in ISO/FDIS 3522: Aluminium and aluminium alloys-Castings-Chemical composition and mechanical properties published in 2006.
| Unit: | Chemical composition (mass %) | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Cu | Si | Mg | Zn | Fe | Mn | Cr | Ni | Sn | Pb | Ti | Al | |
| ADC1 | 1.0 max. | 11.0 to 13.0 | 0.3 max. | 0.5 max. | 1.3 max. | 0.3 max. | — | 0.5 max. | 0.1 max. | 0.20 max. | 0.30 max. | Remainder |
ADC3 |
0.6 max. | 9.0 to 11.0 | 0.4 to 0.6 | 0.5 max. | 1.3 max. | 0.3 max. | — | 0.5 max. | 0.1 max. | 0.15 max. | 0.30 max. | Remainder |
| ADC5 | 0.2 max. | 0.3 max. | 4.0 to 8.5 | 0.1 max. | 1.8 max. | 0.3 max. | — | 0.1 max. | 0.1 max. | 0.10 max. | 0.20 max. | Remainder |
| ADC6 | 0.1 max. | 1.0 max. | 2.5 to 4.0 | 0.4 max. | 0.8 max. | 0.4 to 0.6 | — | 0.1 max. | 0.1 max. | 0.10 max. | 0.20 max. | Remainder |
| ADC10 | 2.0 to 4.0 | 7.5 to 9.5 | 0.3 max. | 1.0 max. | 1.3 max. | 0.5 max. | — | 0.5 max. | 0.2 max. | 0.2 max. | 0.30 max. | Remainder |
| ADC10Z | 2.0 to 4.0 | 7.5 to 9.5 | 0.3 max. | 3.0 max. | 1.3 max. | 0.5 max. | — | 0.5 max. | 0.2 max. | 0.2 max. | 0.30 max. | Remainder |
| ADC12 |
1.5 to 3.5 | 9.6 to 12.0 | 0.3 max. | 1.0 max. | 1.3 max. | 0.5 max. | — | 0.5 max. | 0.2 max. | 0.2 max. | 0.30 max. | Remainder |
| ADC12Z | 1.5 to 3.5 | 9.6 to 12.0 | 0.3 max. | 3.0 max. | 1.3 max. | 0.5 max. | — | 0.5 max. | 0.2 max. | 0.2 max. | 0.30 max. | Remainder |
| ADC14 | 4.0 to 5.0 | 16.0 to 18.0 | 0.45 to 0.65 | 1.5 max. | 1.3 max. | 0.5 max. | — | 0.3 max. | 0.3 max. | 0.2 max. | 0.30 max. | Remainder |
| Al Si9(1) | 0.10 max. | 8.0 to 11.0 | 0.10 max. | 0.15 max. | 0.65 max. | 0.50 max. | — | 0.05 max. | 0.05 max. | 0.05 max. | 0.15 max. | Remainder |
| Al Si12(Fe)(2) | 0.10 max. | 10.5 to 13.5 | 0.10 max. | 0.15 max. | 1.0 max. | 0.55 max. | — | — | — | — | 0.15 max. | Remainder |
| Al Si10Mg(Fe)(1) | 0.10 max. | 9.0 to 11.0 | 0.20 to 0.50 | 0.15 max. | 1.0 max. | 0.55 max. | — | 0.15 max. | 0.05 max. | 0.15 max. | 0.20 max. | Remainder |
| Al Si8Cu3(2) | 2.0 to 3.5 | 7.5 to 9.5 | 0.05 to 0.55 | 1.2 max. | 0.8 max. | 0.15 to 0.65 | — | 0.35 max. | 0.15 max. | 0.25 max. | 0.25 max. | Remainder |
| Al Si9Cu3(Fe)(2) | 2.0 to 4.0 | 8.0 to 11.0 | 0.05 to 0.55 | 1.2 max. | 1.3 max. | 0.55 max. | 0.15 max. | 0.55 max. | 0.25 max. | 0.35 max. | 0.25 max. | Remainder |
| Al Si9Cu3(Fe)(Zn)(2) | 2.0 to 4.0 | 8.0 to 11.0 | 0.05 to 0.55 | 3.0 max. | 1.3 max. | 0.55 max. | 0.15 max. | 0.55 max. | 0.25 max. | 0.35 max. | 0.25 max. | Remainder |
| Al Si11Cu2(Fe)(2) | 1.5 to 2.5 | 10.0 to 12.0 | 0.30 max. | 1.7 max. | 1.1 max. | 0.55 max. | 0.15 max. | 0.45 max. | 0.25 max. | 0.25 max. | 0.25 max. | Remainder |
| Al Si11Cu3(Fe) | 1.5 to 3.5 | 9.6 to 12.0 | 0.35 max. | 1.7 max. | 1.3 max. | 0.60 max. | — | 0.45 max. | 0.25 max. | 0.25 max. | 0.25 max. | Remainder |
| Al Si12Cu1(Fe)(2) | 0.7 to 1.2 | 10.5 to 13.5 | 0.35 max. | 0.55 max. | 1.3 max. | 0.55 max. | 0.10 max. | 0.30 max. | 0.10 max. | 0.20 max. | 0.20 max. | Remainder |
| Al Si17Cu4Mg | 4.0 to 5.0 | 16.0 to 18.0 | 0.45 to 0.65 | 1.5 max. | 1.3 max. | 0.50 max. | — | 0.3 max. | 0.3 max. | — | — | Remainder |
| Al Mg9(1) | 0.10 max. | 2.5 max. | 8.0 to 10.5 | 0.25 max. | 1.0 max. | 0.55 max. | — | 0.10 max. | 0.10 max. | 0.10 max. | 0.20 max. | Remainder |
Notes(1) Chemical components other than those given in the above table, including those shown in the table with “—” i.e., no specification values, shall be 0.05% max. for individual elements and 0.15% in total.
(2) Chemical components other than those given in the above table, including those shown in the table with “—” i.e., no specification values, shall be 0.05% max. for individual elements and 0.25% in total.
| Standard | Japanese Industrial Standard | Related Foreign Standards | ||||
|---|---|---|---|---|---|---|
| U.S.A | U.K | Germany | France | International Standard | ||
| JIS | ASTM | BS | DIN | NF | ISO | |
| Standard Number | H2118:06 | B179:03 | EN1676:97 | EN1676:97 | EN1676:97 | ― |
| Standard Name | Aluminum alloy ingot for die casting | All casting aluminum alloy ingots | Aluminum alloy ingot | |||
| Material Symbol | AD1.1 | A413.1 | ― | |||
| AD1.2 | A413.2 | ― | ||||
| AD3.1 | A360.1 | ― | ||||
| AD3.2 | A360.2 | ― | ||||
| AD5.1 | ― | ― | ||||
| AD5.2 | ― | ― | ||||
| AD6.1 | ― | ― | ||||
| AD6.2 | ― | ― | ||||
| AD10.1 | A380.1 | ― | ||||
| AD10.2 | A380.2 | ― | ||||
| AD10Z.1 | ― | ― | ||||
| AD12.1 | ― | ― | ||||
| AD12.2 | 383.2 | ― | ||||
| AD12Z.1 | 383.1 | ― | ||||
| AD14.1 | B390.1 | ― | ||||
| AD14.2 | 390.2 | ― | ||||
Useful Information
Due to current circumstances, we have temporarily stopped accepting enquiries.
We apologize for any inconvenience caused and we are hoping for your kind consideration.
We apologize for any inconvenience caused and we are hoping for your kind consideration.
